不銹鋼門套線包邊的做法 1.用沖擊電鉆在門四周大洞眼,并插入木楔。

Method for wrapping stainless steel door frame wire: 1. Use an impact drill to create large holes around the door and insert wooden wedges.

2.將15厘 大芯板 (或夾板)靠墻側進行防潮處理(刷 光油 2遍后在貼珍珠棉)。用釘槍校正固定后,再用鐵釘加固。

2. Apply moisture-proof treatment to the 15cm large core board (or plywood) against the wall side (brush with gloss oil twice and then apply pearl cotton). After correcting and fixing with a nail gun, reinforce with iron nails.

門套線條打底用9厘夾板。打底夾板外側用實木線條收口。合頁位置加板襯固或封兩層15厘大芯板。

Use 9cm plywood as the base for the door frame lines. The outer side of the base plywood is closed with solid wood lines. Add board lining or seal two layers of 15cm large core board at the hinge position.

3.門套與門扇相合之處到進門邊的側面用9厘夾板做止口板,止口深度與門的厚度相同。

3. Use 9cm plywood to make a stop plate from the point where the door frame and door leaf match to the side of the entrance, with the depth of the stop plate being the same as the thickness of the door.

4.面板用 白乳膠 涂勻后貼于打第大芯板及止口板上,并用不銹鋼蚊釘適當加固。

4. Apply white latex evenly to the panel and stick it onto the largest core board and stopper board, and reinforce it appropriately with stainless steel mosquito nails.

5.門套線條寬度一般為60mm—80mm.厚度8mm.

5. The width of the door frame line is generally 60mm to 80mm, and the thickness is 8mm

6.廚衛門套線條里側用不銹鋼(啞光)線條為宜。

6. It is advisable to use stainless steel (matte) lines on the inner side of the kitchen and bathroom door frames.

7.門套及 門窗 套垂直、水平誤差不超過2mm(2m以上不超過3mm)對角線誤差不超過3mm(2m以上不超過5mm).

7. The vertical and horizontal errors of door frames and door and window frames shall not exceed 2mm (not exceeding 3mm for 2m and above), and the diagonal error shall not exceed 3mm (not exceeding 5mm for 2m and above)

8.門套兩側墻與門套之間距離在門套線條不能壓住接縫時,宜先用 水泥砂漿 掛鋼釘封平(用板定模灌漿)干燥后方可封板打第,在門套線條能壓住接縫時可用板封龍骨結構。

8. When the distance between the walls on both sides of the door frame and the door frame cannot be pressed against the joint by the door frame line, it is advisable to first use cement mortar to hang steel nails and seal it flat (with board fixed mold grouting) before sealing the board. When the door frame line can press against the joint, the board can be used to seal the keel structure.

9.單面門套用9厘板打底(凸窗應注意 窗簾 位置)。其他與雙面門套同。

9. Single sided door frames should be lined with 9cm boards (attention should be paid to the position of the curtains for protruding windows). Same as double-sided door frames.

入戶大門可封單邊實木線條門套。

The entrance door can be sealed with a single-sided solid wood door frame.

10.窗套不宜包臺面,臺面用 大理石 鋪貼(防盜網宜在窗套面板封后制作)。

10. Window frames should not cover countertops, which should be paved with marble (anti-theft nets should be made after the window frame panel is sealed).

單面門套:在原來有門的基礎上起裝飾作用,不起承受門的力量。 做不銹鋼門套線包邊的注意事項 不銹鋼門套線包邊一般都是定制加工,很少有現場制作的,因為目前工人的技術水平達不檢驗評定標準,而且現場也沒有專業的不銹鋼施工操作人員。

Single sided door frame: It serves as a decoration on the basis of the original door and does not bear the force of the door. Precautions for stainless steel door frame wire edging: Stainless steel door frame wire edging is generally customized and rarely made on site because the current technical level of workers does not meet the inspection and evaluation standards, and there are no professional stainless steel construction operators on site.

本文來自：菏澤拉絲不銹鋼電梯門套線更多的內容請點擊：http://www.caiaiwo.cn 我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

This article is from: Heze brushed stainless steel elevator door frame wire. For more content, please click: http://www.caiaiwo.cn We will provide satisfactory service for the questions you ask. Welcome to call us!