1、材料厚度必需1.2厚（實際厚度不得小于1.08）。安徽電梯套

1. The material thickness must be 1.2 (actual thickness must not be less than 1.08). Anhui Elevator Set

2、必需注意用豎料來收口門頭橫料。

2. It is necessary to pay attention to using vertical material to close the horizontal material of the door head.

3、注意制作基層一定要小于門套包邊尺寸5mm左右，**足夠的空間安裝和打膠。

3. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

4、門頭板寬度要略小于豎料寬度1-2毫米，收口才美觀。

4. The width of the door panel should be slightly smaller than the width of the vertical material by 1-2 millimeters for a beautiful closure.

5、一般門頭板和立面包板對接處的陰角處不建議用膠水收口，這樣既美觀又能檢驗門套安裝質量。

5. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

b：普通的45°拼接門套做法，常規注意事項如下：

b: The common 45 ° splicing door frame method requires the following precautions:

1、材料厚度必需1.2厚（實際厚度不得小于1.08）。注意對角處不能有錯位，焊接點一定要處理在隱蔽位置。

1. The material thickness must be 1.2 (actual thickness must not be less than 1.08). Be careful not to have any misalignment at the diagonal, and the welding points must be handled in concealed positions.

2、注意制作基層一定要小于門套包邊尺寸5mm左右，足夠的空間安裝和打膠。

2. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

3、一般門頭板和立面包板對接處的陰角處不建議用膠水收口，這樣既美觀又能檢驗門套安裝質量。

3. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

安裝質量粗劣，陰角打膠遮蓋瑕疵，不建議使用

Poor installation quality, with defects covered by glue on the inner corners, not recommended for use

c：常規止口門套做法如左下圖，這類做法的弊端：

c: The conventional method of using a stop mouth door frame is shown in the bottom left figure. The drawbacks of this method are:

1、基層不準確時很難卡上去；尺寸不可調節，對于門洞基層有變化時無法改動門套尺寸。

1. It is difficult to get stuck when the grassroots is inaccurate; The size cannot be adjusted, and the door frame size cannot be changed when there are changes in the base layer of the door opening.

2、加工復雜，尺寸較大時運輸會有變形風險。

2. When processing is complex and the size is large, there is a risk of deformation during transportation.

建議使用右上圖做法，這類做法的有點：

It is recommended to use the method shown in the upper right image, which has some advantages:

基層不準確時可以有效的通過結構分解來化解掉；門套寬度可以小范圍調節，能夠適應工地現場的變化。尺寸分解后也降低了加工難度和變形風險

When the grassroots is inaccurate, it can be effectively resolved through structural decomposition; The width of the door frame can be adjusted within a small range to adapt to changes on the construction site. The size decomposition also reduces the difficulty of processing and the risk of deformation

需要注意的是推薦做法要注意不銹鋼電梯門套安裝時兩塊板保持水平，注意第二塊扣板的基層必需準確。

It should be noted that the recommended practice is to keep the two plates level when installing the stainless steel elevator door frame, and to ensure that the base of the second buckle plate is accurate.

以上門套為整體成型，也就是常規的做法，基層不標準造成了拼角出現錯位、閃縫等質量問題。影響美觀，建議止口板和包板分開，可以有效避免因基層問題而造成的安裝瑕疵。

The above door frames are formed as a whole, which is a common practice. The non-standard base layer has caused quality problems such as misalignment and flash joints in the joints. It affects the appearance. It is recommended to separate the sealing plate and the wrapping plate to effectively avoid installation defects caused by grassroots issues.

d：電梯門套常規做法有一部分被擋住屬于不可見面積的優化

d: The conventional practice of elevator door frames is to partially block and optimize the invisible area

常規注意事項如下：

The general precautions are as follows:

1、材料厚度必需1.5厚（實際厚度不得小于1.38）。

1. The material thickness must be 1.5 (actual thickness must not be less than 1.38).

2、門頭板寬度.好小于里面包板的寬度，這樣收口會美觀。

2. Width of the door panel It should be smaller than the width of the inner packaging board, so that the closure will look beautiful.

3、注意制作基層一定要小于門套包邊尺寸5mm左右，足夠的空間安裝和打膠。

3. Note that the base layer must be about 5mm smaller than the edge size of the door frame, with sufficient space for installation and gluing.

4、一般門頭板和立面包板對接處的陰角處不建議用膠水收口，這樣既美觀又能檢驗門套安裝質量。

4. It is not recommended to use glue to close the inner corners of the junction between the door panel and the facade panel, as this is both aesthetically pleasing and can verify the quality of the door frame installation.

5、有的門套立面包板上面有一部分被擋住屬于不可見面積，但是決算

5. Some door frames have a part of the facade panel that is blocked and belongs to the invisible area, but the final settlement

以上節點可以有效解決我們常規門套生產中的不可見面積的浪費現象。同時邊緣卡線富于變化。

The above nodes can effectively solve the waste of invisible area in our conventional door frame production. At the same time, the edge card lines are rich in variation.

門套側板為整塊板決算時造成不可見面積的分歧，但如果采用結構分解為2部分的做法，電梯廳門套使用的是分段處理形成了一條明顯拼接縫隙，可以有效解決這個問題。

When the side panel of the door frame is calculated as a whole, it causes a discrepancy in the invisible area. However, if the structure is decomposed into two parts, the elevator hall door frame is segmented to form a clear joint gap, which can effectively solve this problem.

本文由淄博電梯門套廠家為您提供技術支持，更多精彩內容請點擊我們的網站：http://www.caiaiwo.cn

This article is provided with technical support by Zibo Elevator Door Frame Manufacturer. For more exciting content, please click on our website: http://www.caiaiwo.cn